Person, Clothing, Apparel, Crowd, Huddle, People, Finger, Hand

CNC Machinist II

Technetics Group

 

CNC Machinist II

  • 492808
  • Deland, Florida, United States
  • Technetics Group
  • Operations
  • Full-Time/Regular

JOB SUMMARY:

CNC Machinist II is a mid-level position to perform lathe and mill tasks, continue to learn all aspects of CNC operations, the trade and, and, as a part of the Production Team, fill in as needed in other areas in support of manufacturing.  The requirements listed below are representative of the knowledge, skills and/or abilities necessary to meet the minimum job requirements of this position. 

 ESSENTIAL FUNCTIONS:

  • Maintain safe operations by identifying safety risks and adhering to safety procedures, requirements and regulations.
  • Produces machined parts, assemblies, tool jigs and fixtures by operating and adjusting manual and/or CNC machines, such as, but not limited to, mills, lathes, etc.
  • Performs machine set-ups, tool changes and minor program modifications with limited assistance and/or supervision
  • Verifies settings by measuring positions and first-run pieces in accordance with standards and requirements
  • Utilizes drawings, sketches, and/or verbal/written instructions to safely produce high quality close tolerance parts while detecting defects, troubleshooting malfunctioning processes and other quality assurance procedures and processes.
  • Maintaining the work area safe, clean and organized, assisting 5S and/or general good housekeeping practices
  • Performs minor machine preventative maintenance (PM), as assigned by the Maintenance Manager, Operations Manager or designated representative
  • Documents daily tasks, as required, via designated logs or systems
  • Participate in the “continuous improvement” and LEAN programs to improve, increase throughput and identify cost reductions.

 JOB QUALIFICATIONS:

  • High School diploma/GED or Vocational School equivalent Required: Understands basic safety standards and policies
  • Minimum of 2 years of machining experience
  • Computer literacy, including basic CNC programming experience
  • Basic tool and mechanical aptitude
  • Ability to read and understand basic blue prints and have training or education in Geometric Dimensioning and Tolerancing (GD&T)
  • Ability to utilize and interpret precision measuring equipment
  • Must have competent authority in at least one and more Manual and CNC machines with the ability to machine complex components with lathes and/or mills
  • Ability to conduct set-ups and make offsets for low to medium complexity components with no assistance and minimal supervision
  • Ability to perform basic shop math
  • Must possess strong attention to detail and communication skills
  • Trade Certification (preferred)
  • Coordinate Measuring Machine (CMM) Experience (preferred)
  • Forklift experience and certification (preferred)

SUPERVISORY RESPONSIBILITIES:

This position has no direct supervisory responsibilities.

ADDITIONAL RESPONSIBILITIES:

Performs other duties as assigned by supervisor.

PHYSICAL REQUIREMENTS:

While performing the duties of this job, the employee is regularly required to talk and hear. The employee is occasionally required to stand; walk; sit; use hands to handle and feel material, as well as reach with hands and arms. The employee must occasionally lift and/or move up to 30 pounds. The noise level in the work environment is usually moderate.

 

The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

WORK ENVIRONMENT:

This specification is intended to indicate the kinds of tasks and levels of work difficulty that will be required of positions that will be given this title and shall not be construed as declaring what the specific duties and responsibilities of any particular position shall be. It is not intended to limit or in any way modify the right of any supervisor to assign, direct, and control the work of employees under his/her supervision. The use of a particular expression or illustration describing duties shall not be held to exclude other duties not mentioned. Ability to competently perform all the essential duties of the position, with or without reasonable accommodation, demonstrated commitment to effective customer service delivery, and the ability to work productively as a member of a team or work group are basic requirements of all positions at Technetics Group.

 

Other People Viewed

Quality Technician

493080 Longview Texas United States Longview, Texas, United States STEMCO Quality
Title: Quality Technician Position Type: Full-Time/Regular Division: STEMCO Department: Quality Location: STEMCO Longview Job Summary & Job Duties Title: Quality Technician Position Type: Full-Time/Regular Division: STEMCO Department: Qualit...

Sales Manager-Ontario

493060 Remote Remote STEMCO Sales & Marketing
The Sales Manager is Responsible for meeting established sales goals / targets for the territory.  Supporting the sales and service activity in the assigned geographic areas of responsibility. Conduct product demonstrations and installation traini...

Marketing Leader

493067 Remote Remote STEMCO Sales & Marketing
The Marketing Leader builds awareness of how STEMCO products & services can fulfill our customer and channel partner needs by developing and executing marketing strategies. They create comprehensive campaigns to improve customer retention and enha...

Manufacturing Technician – Final Quality Inspection

493076 Santa Rosa California United States Santa Rosa, California, United States Alluxa Operations, Quality
FQI Role The FQI technician supports the optical thin film process. Duties will include using microscopes and digital equipment to inspect materials for defects as a vital part of the product’s final process. We are seeking technicians with high ...

Manufacturing Technician – Metrology/Lab

493077 Santa Rosa California United States Santa Rosa, California, United States Alluxa Operations, Quality, Supply Chain
Metrology Tech Role The Metrology technician supports the optical thin film process. Duties include loading spectrophotometer equipment, interpreting and analyzing product data, following specifications, department process and nomenclature. Ensure...

Manufacturing Technician – Coating

493075 Santa Rosa California United States Santa Rosa, California, United States Alluxa Operations
Coating Tech Role The Coating technician supports the optical thin film process. Duties will include operating vacuum coating chambers by performing measurements, calibration, and data analysis while maintaining a safe and orderly workspace. We ar...

home_snippet.jpg

GLOBAL PERFORMANCE: Nearly half of annual sales are generated in markets outside the U.S.

Apply Now

Alert me about jobs like this

Not You?

We have emailed you a code to verify your identity

Thank you